1 / 5 www.asb.co.kr november 2008 p lerow tm aln0925at internally matched lna module the plerow tm aln - series is the compactly designed surface - mount module for the use of the lna with or without the following gain blocks in the infrastructure equipment of the mobile wireless (cdma, gsm, pcs, phs, wcdma, dmb, wlan, wibro, wimax), gps, satellite commun i- cation terminals , c atv and so on. it has an exceptional performance of low noise figure, high gain, high oip3, and low bias current. the stability factor is always kept more than unity over the application band in order to ensure its unconditionally stable implementation to the application system environment. the surface - mount module package including the completed matching circuit and other components necessary just in case allows very simple and convenient implementation onto the system board in mass production level. parameter unit specifications min typ max frequency range mhz 890 960 gain db 19 20 gain flatness db ? 0.5 ? 0.7 noise figure db 0.8 0.85 output ip3 (1) dbm 30 31 s11 / s22 (2) db - 14 / - 14 output p1db dbm 16 17 switching time ? sec - supply current ma 70 80 supply voltage v 5 impedance ? 50 max. rf input power dbm c.w 29 ~ 31 (before fail) package type & size mm surface mount type, 10wx10lx3.8h operating temperature is - 40 ? c to +85 ? c. 1) oip3 is measured wit h two tones at an output power of 8 dbm / tone separated by 1 mhz. 2) s11/s22 (max) is the worst value within the frequency band. 3) switching time means the time that takes for output power to get stabilized to its final level after switching dc voltage f rom 0 v to v s . pin number function 2 rf in 5 rf out 6 +vcc other s ground feature s s 21 = 20.5 db @ 890 mhz = 19.5 db @ 960 mhz nf of 0.8 db over fr e quenc y unconditionally stable single 5v supply high oip3 @ low current note: 1. the nu mber and size of ground via holes in a circuit board is critical for thermal rf grounding consider a tions. 2. we recommend that the ground via holes be placed on the bottom of all ground pins for better rf and thermal performance, as shown in the dra w ing at the left side. description (recommended footprint) aln0925at asb inc. (top view) (bottom view) ? 0.4 plated thru holes to ground plane plerow (side view) c o u pl er website: www.asb.co.kr e - mail: sales@asb.co.kr tel: (82) 42 - 528 - 722 3 f ax : (82) 42 - 528 - 7222 more inform a tion c o u pl er c o u pl er c o u pl er c o u pl er 1 - st age single type typ. @ t = 25 ? c, v s = 5 v, freq. = 925 mhz, z o.sys = 50 ohm solder stencil area specifications (in pr o duction) ou t line drawing (unit: mm)
2 / 5 www.asb.co.kr november 2008 p lerow tm aln0925at internally matched lna module s - param e ters noise figure oip3 p1db 890~960 mhz +5 v stability fa c tor (k) typical performance (measured)
3 / 5 www.asb.co.kr november 2008 p lerow tm aln0925at internally matched lna module gain, p1db, and oip3 with te m perature ( - 4 0 ~ 100 )
4 / 5 www.asb.co.kr november 2008 p lerow tm aln0925at internally matched lna module nf, p1db, oip3, and s - parameters with voltage change (4.5 v ~ 5.5 v)
5 / 5 www.asb.co.kr november 2008 p lerow tm aln0925at internally matched lna module 1) the tan tal capacitor is optional and for bypassing the ac noise introduced from the dc supply. the capacitance value may be dete r mined by customer s dc supply status. 2) so - called dc blocking capacitors are always necessarily placed at the input and output port for allowing only the rf signal to pass and blocking the dc component in the signal. the dc blocking capacitors are included inside the lna module. therefore, c1 & c2 capacitors may not be necessary, but can be added just in case that the customer wants. the v alue of c1 & c2 is determined by considering the application fr e quency. preliminary application circuit recommended soldering reflow process evaluation board layout + - aln out in c1 c2 tantal c a pacitor v dc 20~40 sec 260 ? c 200 ? c 150 ? c 60~180 sec ramp - up (3 ? c/sec) ramp - down (6 ? c/sec) size 25 x 25mm in out +vcc (for aln - at, bt, t series C 10x1 0mm)
|
